Next Previous Contents

6. Boot Arguments for SCSI Peripherals.

This section contains the descriptions of the boot args that are used for passing information about the installed SCSI host adapters, and SCSI devices.

6.1 Arguments for Mid-level Drivers

The mid level drivers handle things like disks, CD-ROMs and tapes without getting into host adapter specifics.

Maximum Probed LUNs (`max_scsi_luns=')

Each SCSI device can have a number of `sub-devices' contained within itself. The most common example is any of the SCSI CD-ROMs that handle more than one disk at a time. Each CD is addressed as a `Logical Unit Number' (LUN) of that particular device. But most devices, such as hard disks, tape drives and such are only one device, and will be assigned to LUN zero.

The problem arises with single LUN devices with bad firmware. Some poorly designed SCSI devices (old and unfortunately new) can not handle being probed for LUNs not equal to zero. They will respond by locking up, and possibly taking the whole SCSI bus down with them.

The kernel has a configuration option that allows you to set the maximum number of probed LUNs. The default is to only probe LUN zero, to avoid the problem described above.

To specify the number of probed LUNs at boot, one enters `max_scsi_luns=n' as a boot arg, where n is a number between one and eight. To avoid problems as described above, one would use n=1 to avoid upsetting such broken devices

SCSI Logging (`scsi_logging=')

Supplying a non-zero value to this boot argument turns on logging of all SCSI events (error, scan, mlqueue, mlcomplete, llqueue, llcomplete, hlqueue, hlcomplete). Note that better control of which events are logged can be obtained via the /proc/scsi/scsi interface if you aren't interested in the events that take place at boot before the /proc/ filesystem is accessible.

Parameters for the SCSI Tape Driver (`st=')

Some boot time configuration of the SCSI tape driver can be achieved by using the following:


        st=buf_size[,write_threshold[,max_bufs]]

The first two numbers are specified in units of kB. The default buf_size is 32kB, and the maximum size that can be specified is a ridiculous 16384kB. The write_threshold is the value at which the buffer is committed to tape, with a default value of 30kB. The maximum number of buffers varies with the number of drives detected, and has a default of two. An example usage would be:


        st=32,30,2

Full details can be found in the README.st file that is in the scsi directory of the kernel source tree.

6.2 Arguments for SCSI Host Adapters

General notation for this section:

iobase -- the first I/O port that the SCSI host occupies. These are specified in hexidecimal notation, and usually lie in the range from 0x200 to 0x3ff.

irq -- the hardware interrupt that the card is configured to use. Valid values will be dependent on the card in question, but will usually be 5, 7, 9, 10, 11, 12, and 15. The other values are usually used for common peripherals like IDE hard disks, floppies, serial ports, etc.

dma -- the DMA (Direct Memory Access) channel that the card uses. Typically only applies to bus-mastering cards. PCI and VLB cards are native bus-masters, and do not require and ISA DMA channel.

scsi-id -- the ID that the host adapter uses to identify itself on the SCSI bus. Only some host adapters allow you to change this value, as most have it permanently specified internally. The usual default value is seven, but the Seagate and Future Domain TMC-950 boards use six.

parity -- whether the SCSI host adapter expects the attached devices to supply a parity value with all information exchanges. Specifying a one indicates parity checking is enabled, and a zero disables parity checking. Again, not all adapters will support selection of parity behaviour as a boot argument.

Adaptec aha151x, aha152x, aic6260, aic6360, SB16-SCSI (`aha152x=')

The aha numbers refer to cards and the aic numbers refer to the actual SCSI chip on these type of cards, including the Soundblaster-16 SCSI.

The probe code for these SCSI hosts looks for an installed BIOS, and if none is present, the probe will not find your card. Then you will have to use a boot argument of the form:


         aha152x=iobase[,irq[,scsi-id[,reconnect[,parity]]]]

Note that if the driver was compiled with debugging enabled, a sixth value can be specified to set the debug level.

All the parameters are as described at the top of this section, and the reconnect value will allow device disconnect/reconnect if a non-zero value is used. An example usage is as follows:


        aha152x=0x340,11,7,1

Note that the parameters must be specified in order, meaning that if you want to specify a parity setting, then you will have to specify an iobase, irq, scsi-id and reconnect value as well.

Adaptec aha154x (`aha1542=')

These are the aha154x series cards. The aha1542 series cards have an i82077 floppy controller onboard, while the aha1540 series cards do not. These are busmastering cards, and have parameters to set the ``fairness'' that is used to share the bus with other devices. The boot argument looks like the following.


        aha1542=iobase[,buson,busoff[,dmaspeed]]

Valid iobase values are usually one of: 0x130, 0x134, 0x230, 0x234, 0x330, 0x334. Clone cards may permit other values.

The buson, busoff values refer to the number of microseconds that the card dominates the ISA bus. The defaults are 11us on, and 4us off, so that other cards (such as an ISA LANCE Ethernet card) have a chance to get access to the ISA bus.

The dmaspeed value refers to the rate (in MB/s) at which the DMA (Direct Memory Access) transfers proceed at. The default is 5MB/s. Newer revision cards allow you to select this value as part of the soft-configuration, older cards use jumpers. You can use values up to 10MB/s assuming that your motherboard is capable of handling it. Experiment with caution if using values over 5MB/s.

Adaptec aha274x, aha284x, aic7xxx (`aic7xxx=')

These boards can accept an argument of the form:


        aic7xxx=extended,no_reset

The extended value, if non-zero, indicates that extended translation for large disks is enabled. The no_reset value, if non-zero, tells the driver not to reset the SCSI bus when setting up the host adaptor at boot.

AdvanSys SCSI Host Adaptors (`advansys=')

The AdvanSys driver can accept up to four i/o addresses that will be probed for an AdvanSys SCSI card. Note that these values (if used) do not effect EISA or PCI probing in any way. They are only used for probing ISA and VLB cards. In addition, if the driver has been compiled with debugging enabled, the level of debugging output can be set by adding an 0xdeb[0-f] parameter. The 0-f allows setting the level of the debugging messages to any of 16 levels of verbosity.

Always IN2000 Host Adaptor (`in2000=')

Unlike other SCSI host boot arguments, the IN2000 driver uses ASCII string prefixes for most of its integer arguments. Here is a list of the supported arguments:

ioport:addr -- Where addr is IO address of a (usually ROM-less) card.

noreset -- No optional args. Prevents SCSI bus reset at boot time.

nosync:x -- x is a bitmask where the 1st 7 bits correspond with the 7 possible SCSI devices (bit 0 for device #0, etc). Set a bit to PREVENT sync negotiation on that device. The driver default is sync DISABLED on all devices.

period:ns -- ns is the minimum # of nanoseconds in a SCSI data transfer period. Default is 500; acceptable values are 250 to 1000.

disconnect:x -- x = 0 to never allow disconnects, 2 to always allow them. x = 1 does 'adaptive' disconnects, which is the default and generally the best choice.

debug:x If `DEBUGGING_ON' is defined, x is a bitmask that causes various types of debug output to printed - see the DB_xxx defines in in2000.h

proc:x -- If `PROC_INTERFACE' is defined, x is a bitmask that determines how the /proc interface works and what it does - see the PR_xxx defines in in2000.h

Some example usages are listed below:


        in2000=ioport:0x220,noreset
        in2000=period:250,disconnect:2,nosync:0x03
        in2000=debug:0x1e
        in2000=proc:3

AMD AM53C974 based hardware (`AM53C974=')

Unlike other drivers, this one does not use boot parameters to communicate i/o, IRQ or DMA channels. (Since the AM53C974 is a PCI device, there shouldn't be a need to do so.) Instead, the parameters are used to communicate the transfer modes and rates that are to be used between the host and the target device. This is best described with an example:


        AM53C974=7,2,8,15

This would be interpreted as follows: `For communication between the controller with SCSI-ID 7 and the device with SCSI-ID 2, a transfer rate of 8MHz in synchronous mode with max. 15 bytes offset should be negotiated.' More details can be found in the file linux/drivers/scsi/README.AM53C974

BusLogic SCSI Hosts with v1.2 kernels (`buslogic=')

In older kernels, the buslogic driver accepts only one parameter, that being the I/O base. It expects that to be one of the following valid values: 0x130, 0x134, 0x230, 0x234, 0x330, 0x334.

BusLogic SCSI Hosts with v2.x kernels (`BusLogic=')

With v2.x kernels, the BusLogic driver accepts many parameters. (Note the case in the above; upper case B and L!!!). There are simply too many to list here. A complete description is tucked away in the middle of the driver linux/drivers/scsi/BusLogic.c and searching for the string BusLogic= will put you right on it.

EATA SCSI Cards (`eata=')

As of late v2.0 kernels, the EATA drivers will accept a boot argument to specify the i/o base(s) to be probed. It is of the form:


        eata=iobase1[,iobase2][,iobase3]...[,iobaseN]

The driver will probe the addresses in the order that they are listed.

Future Domain TMC-8xx, TMC-950 (`tmc8xx=')

The probe code for these SCSI hosts looks for an installed BIOS, and if none is present, the probe will not find your card. Or, if the signature string of your BIOS is not recognized then it will also not be found. In either case, you will then have to use a boot argument of the form:


        tmc8xx=mem_base,irq

The mem_base value is the value of the memory mapped I/O region that the card uses. This will usually be one of the following values: 0xc8000, 0xca000, 0xcc000, 0xce000, 0xdc000, 0xde000.

Future Domain TMC-16xx, TMC-3260, AHA-2920 (`fdomain=')

The driver detects these cards according to a list of known BIOS ROM signatures. For a full list of known BIOS revisions, please see linux/drivers/scsi/fdomain.c as it has a lot of information at the top of that file. If your BIOS is not known to the driver, you can use an override of the form:


        fdomain=iobase,irq[,scsi_id]

IOMEGA Parallel Port / ZIP drive (`ppa=')

This driver is for the IOMEGA Parallel Port SCSI adapter which is embedded into the IOMEGA ZIP drives. It may also work with the original IOMEGA PPA3 device. The boot argument for this driver is of the form:


        ppa=iobase,speed_high,speed_low,nybble

with all but iobase being optionally specified values. If you wish to alter any of the three optional parameters, you are advised to read linux/drivers/scsi/README.ppa for details of what they control.

NCR5380 based controllers (`ncr5380=')

Depending on your board, the 5380 can be either i/o mapped or memory mapped. (An address below 0x400 usually implies i/o mapping, but PCI and EISA hardware use i/o addresses above 0x3ff.) In either case, you specify the address, the IRQ value and the DMA channel value. An example for an i/o mapped card would be: ncr5380=0x350,5,3. If the card doesn't use interrupts, then an IRQ value of 255 (0xff) will disable interrupts. An IRQ value of 254 means to autoprobe. More details can be found in the file linux/drivers/scsi/README.g_NCR5380

NCR53c400 based controllers (`ncr53c400=')

The generic 53c400 support is done with the same driver as the generic 5380 support mentioned above. The boot argument is identical to the above with the exception that no DMA channel is used by the 53c400.

NCR53c406a based controllers (`ncr53c406a=')

This driver uses a boot argument of the form:


        ncr53c406a=PORTBASE,IRQ,FASTPIO

where the IRQ and FASTPIO parameters are optional. An interrupt value of zero disables the use of interrupts. Using a value of one for the FASTPIO parameter enables the use of insl and outsl instructions instead of the single-byte inb and outb instructions. The driver can also use DMA as a compile-time option.

Pro Audio Spectrum (`pas16=')

The PAS16 uses a NCR5380 SCSI chip, and newer models support jumper-less configuration. The boot argument is of the form:


        pas16=iobase,irq

The only difference is that you can specify an IRQ value of 255, which will tell the driver to work without using interrupts, albeit at a performance loss. The iobase is usually 0x388.

Seagate ST-0x (`st0x=')

The probe code for these SCSI hosts looks for an installed BIOS, and if none is present, the probe will not find your card. Or, if the signature string of your BIOS is not recognized then it will also not be found. In either case, you will then have to use a boot argument of the form:


        st0x=mem_base,irq

The mem_base value is the value of the memory mapped I/O region that the card uses. This will usually be one of the following values: 0xc8000, 0xca000, 0xcc000, 0xce000, 0xdc000, 0xde000.

Trantor T128 (`t128=')

These cards are also based on the NCR5380 chip, and accept the following options:


        t128=mem_base,irq

The valid values for mem_base are as follows: 0xcc000, 0xc8000, 0xdc000, 0xd8000.

Ultrastor SCSI cards (`u14-34f=')

Note that there appears to be two independent drivers for this card, namely CONFIG_SCSI_U14_34F that uses u14-34f.c and CONFIG_SCSI_ULTRASTOR that uses ultrastor.c. It is the u14-34f one that (as of late v2.0 kernels) accepts a boot argument of the form:


        u14-34f=iobase1[,iobase2][,iobase3]...[,iobaseN]

The driver will probe the addresses in the order that they are listed.

Western Digital WD7000 cards (`wd7000=')

The driver probe for the wd7000 looks for a known BIOS ROM string and knows about a few standard configuration settings. If it doesn't come up with the correct values for your card, or you have an unrecognized BIOS version, you can use a boot argument of the form:


        wd7000=irq,dma,iobase

6.3 SCSI Host Adapters that don't Accept Boot Args

At present, the following SCSI cards do not make use of any boot-time parameters. In some cases, you can hard-wire values by directly editing the driver itself, if required.

        Adaptec aha1740 (EISA probing),
        NCR53c7xx,8xx (PCI, both drivers)
        Qlogic Fast (0x230, 0x330)
        Qlogic ISP (PCI)


Next Previous Contents